Home > News > About A-Best Jewelry >
Home > News > About A-Best Jewelry > jewelry master model

jewelry master model

Posted on 2014-08-08, By A-Best Staff

Jewelry Master Model - Jewelry Prototyping

VLT silicone molding rubber – jewelry prototyping process
Figure 1: The VLT™
Silicone Molding Rubber.

objet 3d models – rapid jewelry prototyping
Figure 2: Placing the
Objet model inside the mold.

 Finished mold can be complex with even spiral plugs.
Figure 3: Finished mold
can be complex with even
spiral plugs.
 

 The resin Release Spray.
Figure 4: The resin
Release Spray.

Objet Jewelry Models.
Figure 5: Objet Jewelry
Models.

Silicone Molding Rubber is soft and pliable, with a  consistency like putty or molding clay.
Silicone Molding Rubber is
soft and pliable, with a 
consistency like putty or
molding clay.

Place the Objet model inside the Silicone Mold.
Place the Objet model inside
the Silicone Mold.

Placing and embedding the rubber onto model.
Placing and embedding the
rubber onto model.

Curing Silicone Jewelry Molding Rubber Molds involves no  mixing, and at low temperature.
Curing Silicone Jewelry Molding
Rubber Molds involves no 
mixing, and at low temperature.

The Silicone Jewelry Molding  Rubber Molds are then to be  cut and opened by hand.
The Silicone Jewelry Molding 
Rubber Molds are then to be 
cut and opened by hand.

Parting lines are easily  controlled a and corrected  by hand when used with the  powder separation.
Parting lines are easily 
controlled a and corrected 
by hand when used with the 
powder separation.

Finished molds can be  complex with cores, straight  plugs or even spiral plugs.
Finished molds can be 
complex with cores, straight 
plugs or even spiral plugs.





 

Jewelry Molds Using VLT Rubber

Overview - Rapid Jewelry Prototyping Process

 

The recent introduction of Castaldo®’s VLT™ [Very Low Temperature] molding rubber opens the way to a new time-saving process for jewelry prototyping using molding, by Objet Eden™ 3D Printers Systems. The new rubber allows users Objet users to utilize their PolyJet™ patterns as master models for rapid jewelry prototyping and mold them in as little as one hour. This eliminates the need to go through the time-consuming process of creating a metal master model in the jewelry prototyping process.

 

Direct casting of resin models made by most rapid prototyping systems do not burn out cleanly. However, using cold-mold compounds that do not damage the pattern and an RP system that supports the specialized material offers the perfect alternative for rapid jewelry prototyping.

Another recently developed alternative method involved making a liquid rubber mold of the model, curing it overnight, injecting the wax, and then casting the wax (another overnight process) to get the master model. Finally, they make a traditional rubber mold, shoot waxes, and start production casting. All together, the process would take more than two days.

Many casters, while still preferring to make a mold of the resin model and shoot waxes are unhappy with the long curing times: quite simply, they want to make their jewelry prototype models as fast as possible.

 

Jewelry Prototypes - New Methodology

 

Now this entire process of rapid jewelry prototyping can be done in less than half the time. Rubber can be cured at temperatures ranging from 160°F (71°C) to 180°F (83°C), well below the softening point of most resin materials. At a temperature of 160°F, a standard 3/4-inch mold will be cured and ready for injection in 90 to 120 minutes. At 180°F, that time is further reduced to just 30 to 45 minutes. However, as with traditional casting rubbers, longer curing times mean better molds – the longer the cure, the more likely it is that the rubber will flow into every nook and cranny of the jewelry model to provide detail. In addition, when VLT™ rubber cures, it shrinks just 1.4 percent.

Perhaps one of the greatest benefits of VLT™ rubber in the jewelry prototyping process is that it makes rapid prototyping more useful for mass production. Specifically for the jewelry industry, enabling PolyJet™ models to be used directly as master models is a important development because it offers significant time savings in a market where time can be a vital competitive edge.

 

Practical Jewelry Prototyping Processing

On a practical level, it is too expensive and time consuming to run a rapid prototyping machine a thousand times in order to create the high number of castings needed. Now, with VLT™ rubber and PolyJet™, a prototype piece can be directly molded, and the subsequent wax models can be used to make thousands of castings.

 

VLT™ rubber also works well with traditional hand-carved waxes. And, VLT™ rubber is designed specifically for molding – i.e. it acts like any other molding rubber, only at much lower temperatures.

Essentially, the VLT™ and PolyJet™ methodology leverages traditional technology, tools, and techniques. This means there is no one needs to learn anything new, buy new equipment, or train people in new techniques. If you are already doing lost-wax casting, the VLT™ and PolyJet™ methodology fits right in.

 

How does Jewelry Prototyping work with VLT™ ?

Castaldo®  VLT™ Silicone Molding Rubber can be vulcanized at any of a wide range of time and temperature combinations, depending on the characteristics and requirements of the model material. Below are some suggested combinations for a typical mold that is 3/4" / 19 mm thick

 

88° C / 190° F for 30 minutes
82° C / 180° F for 45 minutes
76° C / 170° F for 60 minutes
71° C / 160° F for 90 minutes

The only change from established mold making techniques required by Castaldo® VLT™ Silicone Molding Rubber may be the need to coat the plastic model with a release spray before vulcanizing to ensure easy release of the model after vulcanization. Teflon® (PTFE) sprays work very well, as do common household cooking oil sprays made with olive oil or canola oil, such as PAM®. Wax models do not need to be sprayed.

Key advantages of Rapid Jewelry Prototypes & VLT

Tools and technology
The VLT™ and PolyJet™ methodology utilizes the simple tools and easy technologies you already have and know how to use.

Easy to work with
VLT™ Silicone Molding Rubber has the consistency of modeling clay or putty, reducing mold packing time to a few minutes. There is no need to cut and shape the pieces to fit the mold frame. Merely pull off a piece with your fingers and push it into the mold frame as desired.

 

 

Easy to cut
Molds made of VLT™ rubber are firm, yet they “cut like butter”.

Minimal shrinkage
Rubber shrinkage is only 1.4%

Easy, spray-less release of wax injections
Finished molds require no mold release spray. Wax patterns release easily because the rubber already contains anti-stick compounds.

High-shine finish
Molds made of VLT™ rubber provides waxes with an extremely shiny finish, reducing the polishing work required on your casting.

High tear strength
For a silicone rubber compound, VLT™ rubber is exceptionally high in tear strength, meaning that molds made from it last for years.

Cheaper and easier than RTVs
Room temperature vulcanizing (RTV) compounds require exact measuring and exact mixing. They have limited working times and require vacuum de-bubbling to provide usable molds.

VLT™ Rubber Specifications

Sizes:

Regular strips: 18" x 2 7/8 " x ~3/8" (45.7cm x 7.3cm x ~6mm). Packaged in 5lb (2.27kg) cartons.
Double-wide strips: 18" x 5 3/4" x ~3/8" (45.7cm x 14.5cm x ~6 mm). Packaged in 10Ib (4.5kg) boxes.

Storage:
As with any unvulcanized rubber compound, store away from any source of heat and light. Unvulcanized shelf life is at least one year if properly stored.

Jewelry Prototyping & VLT™ Processes

Castaldo® VLT™ Silicone Molding Rubber is compatible with all mold making techniques, including mold cutting and powder and cream separation molds. It is particularly adaptable to the powder and cream separation processes since the parting line is so easily controlled. For patterns strong enough to resist some pressure, merely push the model into rubber to the desired point. If not satisfied with the results, remove the model, smooth the rubber over with your finger or tool and re-insert the model.

 

Disclaimer
Objet Geometries LTD is not responsible for misuse of our products or their use in conjunction with unsafe or improperly maintained equipment or for uses other than intended as jewelry casting mold making material.



 
 
 
 
 
 
   
     
 
 
 
 
 

 

Print  Close  Top
Related Jewelry News